Home > How To > {SOLVED}Slave Drive Configuration

{SOLVED}Slave Drive Configuration

Contents

Do I just set the new drive as slave until I load the image to it and then powerdown and remove the old drive and set the new one to master? All I want to do is get the info off the drive and toss it. I can pull it out by just removing 1 screw. I'm familiar with computers but this is the first dual setup I have seen. weblink

IT COULD!!!! I had the same situation, old drive with important files, righ clicked the import foreign disks, and bam! Is there any way to change the configuration of my System? I would like to use this computer to recover my data from a Samsung Spin Point (IDE) SV0813H, Hard Disk (XP) and a Seagate U Series 5 (IDE)ST340823A (ME) Hard Disk. http://www.tomshardware.com/answers/id-2503823/setting-ata-drives-master-slave.html

What Is A Slave Hard Drive

Some may argue that people like me who may find it easy to understand, why shouldn't the newbies? On the next screen select either Primary or Extended Partition and left-click on Next to continue. my email address is: [email protected] thanks Reply dg says: March 10, 2008 at 3:49 pm hi, i hav just purchased a seagate 250GB sata drive. This is VERY time-consuming usually.

The Hard Drive only came with a CD, no floppy disk. Your BIOS may have more settings than Cylinders, Heads, and Sectors; if so, simply enter 0 for them. Reply Ryan says: July 30, 2007 at 10:19 pm I don't recall stating that it was too hard for myself to understand. Master Slave Computer Setup Reply Gwen says: February 9, 2009 at 7:18 pm Would like to know the same answer of not format=ting the second (slave) hard drive.

Thank you. It's not your job to go around examining articles and deciding whether or not they are suitable for people who don't understand the basics of what the article is about. The system may be a bit convoluted but I can use it for that. I would uninstall Norton then reinstall it.

All Rights ReservedAd Choices The information on Computing.Net is the opinions of its users. How To Set Up A Slave Drive I have checked Set-up/BIOS- it is all there (but ghosted? However, I am still stumped. Then I bought a 15GB drive.

How To Slave A Hard Drive Windows 7

Report • #7 danieloconnor June 20, 2011 at 21:53:05 thanks everyone! https://forums.techguy.org/threads/solved-slave-drive-configuration.33044/ Saved me a lot of ‘messing about' time. What Is A Slave Hard Drive I opened up the case, following your instructions. Master And Slave Drive Explained If your current hard drive is set as "Cable Select" (meaning it is the only drive on the channel), then you may need to change it to "Master" which will allow

SATA Drives - MasterSlave? http://webadapt.org/how-to/solved-cdrom-drive-problems.php I have a spare one which i utilize as of time while awaiting for its replacement. Seagate 250 GB hard drive 4 gigs ram intel 8800 quad 4 750 watt cooler master power supply Blu-ray burner/player Report lucinda- Dec 5, 2008 at 05:57 PM "i actually have If this is really confusing to you, let me know, and I'll simplify. How To Slave A Hard Drive To Recover Data

Connect the IDE Interface Cable to the Motherboard: Attach the blue end of the IDE interface cable to the 40-pin connector on the motherboard. HELP! QUESTION: How do I configure the drives correctly so that the information is consistant thoughout the machine? check over here Drives are numbered as follows: drive 0 being the boot drive and drive 1-3 are all other drives.

Pete and worked in Tampa "Seminole Heights" for a couple of years. How To Make A Slave Drive Was that bad? Me too!

I think anyone who is attempting to install a new hard drive themselves should embrace the inner geek and get the job done properly… Not that something like this even requires

As I write this, 500gb of new hard disk space is slowly formating into existence, and soon my now dwarfish primary disk will have space to spare. Where and how are the cables connected? If you are simply installing a secondary drive, boot into Windows. How To Partition A Hard Disk xxx Reply walter says: August 17, 2007 at 12:47 am Hello, I've been tring to install a SATA hard drive with no luck.

For assistance with installing Windows please contact Microsoft Support. Cher Reply Kieron says: August 22, 2007 at 11:25 am How do I set up a slave hard drive in windows without formatting it as I have information on it. The rest are by people who can't drive any better than a drunk. this content D+ Reply Stefen Kaur says: November 11, 2008 at 12:50 pm I have a question.

p.s. Reply Michelle says: March 6, 2009 at 7:59 pm Help! But I cannot get my second Western Digitial EIDE Hard Drive recognized. Don't force them.

However, there is often a diagram on the top of the drive telling you how to set the jumpers, and if not there will certainly be instructions in your hard drive's Boot your system up, you should be able to then go to my computer, and see your old hard drive. I bought a new hard drive and used the Restore CD to format it. If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members. {SOLVED}Slave drive configuration Discussion in 'Hardware' started by IGI, May 29, 2000.

Report tjmartineau 38Posts Friday September 19, 2008Registration date December 23, 2008 Last seen - Dec 23, 2008 at 06:00 PM Did you format the drive? (In disk management, where it's saying See Item number: 400008690027 on ebay Dave Reply Jeremy says: August 21, 2008 at 9:28 am Thank you very much for this… I was stuck until I read the section regarding You can still partition the drives if you want. I can't just clone the drive or transfer files as the old drive is corrupted.

One problem though - after setting up the new drive and using Norton Ghost 10.0 to clone the old drive, I can't boot from the new drive. It happen while I was surfing Digg, > off it went, and all I had was a black screen and a huge paper weight. Edit the partition size. Reply mark says: December 18, 2008 at 12:29 pm working on a computer with two hard drives.

I installed just as you said. I have My Pri Master and DVD burner on IDE0, and I needed to add 2 more HDD from my old computer to pull information off, and use them as more Select the ammount of space you would like on your second partition. What I am not sure about is if the second hard drive should automatically store overflow data from the first drive same just as if the first drive were twice as

Yes No Not Helpful 0 Helpful 1 Unanswered Questions My IDE hard disk is locked, how to unlock without my password? In the part of the BIOS that shows how everything is set up, it doesn't show either of the two newer drives, so I'm hesitant to expirament, as I don't see