Home > How To > 2 Comps Off One Cable Modem Help.

2 Comps Off One Cable Modem Help.

Contents

I want to connect two computers upstairs to two ports on my AT&T U-Verse router without having to run two cables. –Michael Jul 31 '15 at 2:31 1 @Michael From This distance, however, changes based on the power of the devices involved, the environment and (most importantly) the Wi-Fi standard. We were hunting the cause of excessive packet errors in the factory. Router #1 will hand out an IP address to router #2's WAN port (in LAN to WAN) and it doesn't matter one bit which IP address it is. check over here

If you're not already familiar with forums, watch our Welcome Guide to get started. So if this person authorized their cable modem on their friend's/relative's Cox account, would that work for them in my house?Would they be using my "line" or would anything they do This is partly because the cap speed is determined in controlled, interference-free environments.) The fastest peak real-world speed of an 802.11ac connection I've seen so far is around 90MBps (or 720Mbps), The only way to avoid a reflection at the bottom of the spring would be to have enough give to prevent a like-phase reflection, but not so much give as to http://www.tomshardware.com/forum/21986-42-computers-cable-modem-modem

How To Connect Internet For Two Computers With One Modem

Currently, there are a few methods used to protect a Wi-Fi network, called "authentication methods": WEP, WPA and WPA2, with WPA2 being the most secure while WEP is becoming obsolete. I wanted devices connected wireless to either router to be able to work as together as a Windows HomeGroup (home network) for printer and file sharing. uniqs74924 Share « [AZ] DPQ3212 Firmware and Channel bonding Question.. • [VA] Increase my bundle still no increase in speed » [email protected] foxiecoxie Anon 2013-Apr-30 12:09 am [OK] Can we connect Show Ignored Content As Seen On Welcome to Tech Support Guy!

Then it's actually fun! This is similar to going to a coffee shop to get a small cup of coffee and the only option is the extra large. Your ISP may have some option where they'll lease you a router and come out to set it up. One Ethernet Cable Two Devices Flag as duplicate Thanks!

i have comcast as my ISP the tech says i have to have 2 accounts to do it but i think it is possible to use just the one account any How To Connect Multiple Computers To One Router up vote 28 down vote favorite 10 I thought the Ethernet is logically a one-line communication bus (for argument's sake, I am excluding hubs). Nice and pretty wall plate that has both an Ethernet jack and a rg6 (cable) jack. Thanks for all your hard work helping people!"..." more - Tom Ta "It was easy to follow the directions.

I want to block the 2nd router from connecting to the internet. How To Share Internet Connection Between Two Computers Using Lan Also, a Wi-Fi connection takes place on just one band at a time. Flag as duplicate Thanks! Wird verarbeitet...

How To Connect Multiple Computers To One Router

In order to maintain a good connection, it should be placed in a location where it gets at least 50% signal strength from the primary router.

However, this requires manually configuring the IP addresses, or using a special crossover cable, for the connection to work. How To Connect Internet For Two Computers With One Modem In short, LAN ports on a router allow Ethernet-ready devices to connect to one another and share data. How To Split Ethernet Cable Into Two Not the answer you're looking for?

The cards involved must have been able to tolerate it. check my blog This metaphorical cable is as long as the range of a Wi-Fi signal broadcast by an access point. If you are creating a LAN-to-WAN network, plug the other end into the WAN port of the secondary router. With this in mind, make sure you buy a switch with significantly more ports than the number of clients you intend to add to the network. How To Connect Two Modems In One House

Are you guys hearing about this a lot?I'm very worried that this is being done by manual-illiterate home computer users that don’t know/care about firewalls and compatibility. Wi-Fi client: A Wi-Fi client or WLAN client is a device that can detect the signal broadcast by an access point, connect to it and maintain the connection. The moment you plug a device into a router, you have yourself a wired network. http://webadapt.org/how-to/2-pc-s-to-1-cable-modem.php In real-world testing so far, with the same amount of streams, I've found that 802.11ac is about three times the speed of Wireless-N, which is still very good. (Note that the

DarkSavage101Jul 11, 2011, 8:30 AM I am attempting to do the same thing, however:My modem has a switch connected to it and both my computers are then connected to the switch, Linksys Se2500 He was setting up a computer on DSL that he had built, and asked me how to set this thing up on USB. Connect the primary router to your modem.

This means that, unlike a dual-band AC1900 router that has one 2.4Ghz band and one 5Ghz band, a tri-band router -- such as the Netgear R8000 or the Asus RT-AC3200 --

To put it differently, if your router has more than one exit port, it also has some switch capabilities. –Bruno9779 Jun 6 '14 at 17:54 1 Actually, it does work, more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed Join our site today to ask your question. Cable Modem With Multiple Ethernet Ports You can change this preference below.

colinsp replied Feb 1, 2017 at 1:40 AM ***COMPUTER HAS BEEN BLOCKED*** wannabeageek replied Feb 1, 2017 at 1:00 AM Huge font and scroll bar problem davehc replied Feb 1, 2017 Older devices and desktop computers that don't can be upgraded to that via a USB or PCIe Wi-Fi adapter. Melde dich bei YouTube an, damit dein Feedback gezählt wird. have a peek at these guys is it possible to replace the router with a switch? (so ethernet cable comes out of the cable modem, goes into the switch and the 2 computers are connected to the

Typically, a good Wi-Fi network is most viable within about 150 feet from the access point. wikiHow Contributor Using the same password isn't a problem. Since this router will be handling the connection to the internet, set it up as if you were only using a single router. fredwestonOct 5, 2006, 2:32 AM Quote: the 6100 has a built in firewall That's probably why you can connect using both USB and Ethernet.

Wireless networking A wireless network is very similar to a wired network with one big difference: devices don't use cables to connect to the router and one another.