Home > Hard Drive > {SOLVED}Master/Slave Setup On Hard Drives

{SOLVED}Master/Slave Setup On Hard Drives

Contents

Reply Mark barbee says: August 31, 2009 at 7:25 pm Here's one for ya. Finding the manager and getting it to format so I could see it on my computer was the missing step. EditRelated wikiHows How to Upgrade a Processor How to Update Your Computer's BIOS How to Ground Yourself to Avoid Destroying a Computer with Electrostatic Discharge How to Find and Update Drivers Depending on your computer model it will be either "Delete," or "F2." Press it a few times before your Operating System (Windows, etc.) starts up. weblink

Thanks for your reply. A lot of people like to use what is called Cable Select. If not, select the auto-detect option. Up next How to Install a Second SATA Hard Drive - Duration: 3:17. find this

What Is A Slave Hard Drive

one of the 20 GB is Primary and the other two are slaves. So I asked could you save my lost data and I will spend more money with you and he said no? Most likely you set your jumper wrong. The newer drives especially make more heat, but a well ventilated case should adequately dispose of the heat.

Reply Spiv says: March 2, 2008 at 11:49 pm Hi there, I have a notebook with a Fujitsu MHT 2040AT, (40GB 4200rpm HD). I have lots of data on there that I need to keep can I install it without formatting? Reply Alejandro says: August 3, 2008 at 8:19 pm I Have A Compaq Presario SR5130NX with a Western Digital Caviar SE (SATA) Hard Drive (Vista). Master Slave Hard Drive Jumper Settings Reply Brett says: June 4, 2009 at 2:31 pm Thanks so much for this post.

Would this be my hard drive. Joshcore, if you are blindly defending your precious website PC Mech, then please, at least have a decent reason to do so. xxx Reply walter says: August 17, 2007 at 12:47 am Hello, I've been tring to install a SATA hard drive with no luck. Cheers Tim Reply Donny says: January 3, 2009 at 4:19 pm Fantastic article!!

Thanks, matey! How To Install A Second Sata Hard Drive In Windows 7 Even I could understand it………… Once again, many thanks. All I want to do is get the info off the drive and toss it. thanks!!

Master Slave Hard Drive Setup

Check the jumpers on the back. expertvillage 67,449 views 2:22 PRESS F1 TO BOOT ERROR ON PC FIX - Duration: 2:55. What Is A Slave Hard Drive By the fifth sentence, ‘Serial ATA'. How To Slave A Sata Hard Drive hak1985org 92,371 views 15:13 Hard Drive Recovery Tutorial - How To Slave Desktop Hard Dri - Duration: 3:31.

Do I require any jumpers on these drives if I were to hook up 2 SCSI drives together? have a peek at these guys An error (403 Forbidden) has occurred in response to this request. Follow this Windows 10 Redstone 2 14894 … How to Update Windows 10 to Threshold 2 with Backups?. 2015-12-01 14:57:14 Tracy King - Here in this passage you’ll find detail steps spotmausoftware 26,490 views 2:50 Setting Jumper Settings on Drives - Duration: 2:24. Sata Hard Drive Slave Jumper Setting

Thanking you, Yours truly, B.Ranganathan Reply Michael says: March 6, 2009 at 5:08 pm Thanks. Protect the drive from static discharge by wearing a grounded wrist strap. Did I get a bad drive or is there something that I need to do to get the new drive to be recognized as the boot drive? check over here Registration is free and the forums are specifically for tech issues such as yours.

Plug the system in and turn it on. Difference Between Master And Slave Drive Though SATA port have no Master and Slave connector, so you will have to figure it from BIOS unless ur system autodetect the master slave connections.For More Information Watch this Link: Privacy Policy | License | Terms & Conditions | Uninstall | Resource | Data Recovery Solution | iPhone Recovery | Android Recovery PCMechHome Sign Up About PCMech Meet The Team

Cheers!

However, there isn't one WD SATA HD in the explorer. Your page sent me through the steps I needed and "I'm OK now" Thanks guys, I'll be back! Reply LD says: August 11, 2007 at 5:11 pm Hi, I had two hard drives installed on my computer. Sata Master Slave I have to start at "start windows normally" and then tries to boot further but then blue screens and says disc drive is not configured properly.

How do you format a HD that you cant see then? Thhe only way it will let me allocate a letter is if i select it as removable drive- then it appears in ‘My Computer' and asks if i want to format and i cant figure out how to get past this and what is wrong? this content I have told CMOS about the Hard Drive, but it still won't boot, and I get errors.