Home > Hard Drive > [SOLVED] How Do I Change My Jumper To Cd Rom Drive?

[SOLVED] How Do I Change My Jumper To Cd Rom Drive?

Contents

ie - read cd, write hdd, read cd, write hdd... The first hard drive is SATA, the second which came from an older computer is IDE. For Serial ATA drives (SATA), you don't need to worry about jumpers at all. Alden28-Aug-09, 19:20Just added my old CD drive into it. have a peek here

If I shut the PC down and restart it, everything appears to run OK. ajgraphcs, Jan 31, 2002 #5 Sponsor This thread has been Locked and is not open to further replies. If your current hard drive is set as "Cable Select" (meaning it is the only drive on the channel), then you may need to change it to "Master" which will allow You could go here:http://www.memtest.org/and download an image file for floppy or cd (probably a floppy version in your case since you can't boot from cdrom) and test the ram. check it out

Windows 10 Not Detecting Second Hard Drive

The cramped 3gb left on my drive will no longer bog me down or limit my media. A loose or in some cases failing IDE cable (assuming it is an IDE and not SATA connection) will produce these errors in the Pavilion line (and most others I would Reply mark says: October 15, 2008 at 7:00 am Hi Did you sort out this issue as I have the same issue? Computer systems are still way too complicated for the average user!

Do save any data you have eg documents or pictures etc and do not forget to save any emails which are a pain because they are stored in the Documents and However, I am still stumped. In general, the master drive should use the black connector on the end and the slave should use the gray connector in the middle, but if each drive is set either Internal Hard Disk Not Detected In Bios Thanks, hope to hear from you or another one of the commenters soon.

Since you say it will boot on occasion the failure may not be severe enough at this stage to completely fail, but a total inability to boot may be looming on Step two: If your drive is getting power and will not open or close, it is time for the paper clip trick. Solved all my problems putting my new S-ATA HDD in under Vista. this page If i were to plug it in, would it be able to recgonise it?

The same thing happened when I removed it. Not Recognizing External Hard Drive My PC is running on 2000XP with FAT32. So now the data connects by SATA instead of IDE. If so, try disabling floppy drive detection in the BIOS altogether and see what it does.

Second Hard Drive Not Showing Up In Disk Management

asus p5q mobo nvidia 8800 graphics card WD 750 GB hard drive. https://books.google.com/books?id=QVZ3k_kTQ-oC&pg=PA295&lpg=PA295&dq=%5BSOLVED%5D+How+do+I+change+my+jumper+to+cd+rom+drive?&source=bl&ots=fnErTGjg4R&sig=Qh7oX2RMql5ExDMXYMsQMK7imnA&hl=en&sa=X&ved=0ahUKEwiR--ShjczRAhUKw Especially from WinXP 32bit to Vista 64bit. Windows 10 Not Detecting Second Hard Drive Reply Sean John November 18, 2009 at 12:02 am Good article. Secondary Hard Drive Not Detected In Bios It's not your job to go around examining articles and deciding whether or not they are suitable for people who don't understand the basics of what the article is about.

however, if you're one that does not understand any of this info, or part of this awesome info…then go google it elsewhere…speaking of google…great tool to "look-up" info about this you navigate here I need the old drive in order to run the image software, as I don't have a boot CD or the windows disks on hand. Reply vince says: March 26, 2013 at 2:21 pm for one if the NEWB reads this it will perk his interest. If you are replacing the old drive, slide the new drive in right where the other one came out. Second Hard Disk Not Detected Windows 7

I tried numerous times, no change.Now I just want to rearrange my IDE cables and drive jumper settings to reflect a boot from the Cd/Rom drive with the OS disc inserted...but hello!!! That's probably why only the PS/2 keyboard worked for you.message edited by DAVEINCAPS Report • Start a discussion Ask Your QuestionEnter more details...Thousands of users waiting to help!Ask now Weekly Poll Check This Out Preview post Submit post Cancel post You are reporting the following post: Disk boot failure: What is it and what can I do to resolve it This post has been flagged

Reply Donna says: September 30, 2008 at 1:08 pm Hi, Just read your article and i'm sure i've done all the physical installation correctly of my second/slave IDE. How To Get Windows To Recognize Ssd I want to say Thank YOU!!! Your primary drive should always be set master or cable select.

If I find an answer in the near future I will post it here.

From this point I have once had Windows work sucessfully but when powered down completely the machine reverted to not seeing the hard drive in bios and only the two dvd The original drive with the older XP version refused to recognize the second physical drive! However, when I loaded XP the icons did not appear and I no programs are on the hard drive. How To Detect New Hard Drive Windows 10 Any help greatelt appreciated!!

But in Windows one of the two drives doesn't appear. That can an may well, damage the motherboard.The idea of depressing the power/start button is to discharge the power supply capacitors. and i cant figure out how to get past this and what is wrong? http://webadapt.org/hard-drive/solved-second-hard-drive.php foe example, stick a PIO only optical drive on with a ultra dma drive and both will drop to pio mode because the optical can't "speak" dma.another issue with having both

Reply Giga says: August 19, 2007 at 12:07 am thenson, the guy who told you your your computer was fried was probably a jerk and put the virus on himself. I have lots of data on there that I need to keep can I install it without formatting? Maybe it will stop the questions – but I doubt it! How about installing a new and different hard drive in a laptop?

Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? So I asked could you save my lost data and I will spend more money with you and he said no? That way, Primary boot will be your sata drive your old hard drive will take your dvdrom's drive letter (D) Ask a question Member requests are more likely to be responded It requires manufacturers to provide owners and independent repair businesses with fair access to service information and replacement parts.

Reply Natalie says: March 13, 2009 at 1:22 pm I recently puchased completely new parts to build a new computer. But what is a USB dongle?. Open it by right-clicking on My Computer and selecting manage.